Skip to content

Saniflo 082 Saniaccess 3 Macerating Pump

SKU 082
by Saniflo
Original price $1,089.00 - Original price $1,089.00
Original price
$1,089.00
$1,089.00 - $1,089.00
Current price $1,089.00
Availability:
in stock

The Saniaccess 3 is a 1/2 HP pump system used to install a complete bathroom up to 15 feet below the sewer line or even up to 150 feet away from a soil stack. It incorporates a macerating system that can handle human waste and toilet paper in residential applications. The blade is made out of a hardened stainless steel material, which eliminates any service or replacement.

*All items may be purchased separately.  However, the Saniaccess 3 works as a system, and therefore a toilet bowl (083 or 087), toilet tank (005), and the macerating unit (082) need to be purchased.  You can buy the bundle here.

    Carbon-neutral shipping with Shopify Planet
    Carbon-neutral shipping on all orders
    2,938kg
    shipping emissions removed
    That's like...
    7,521
    miles driven by an average gasoline-powered car
    We fund innovations in...
    Direct Air Capture
    Bio Oil
    Mineralization

    Specifications

    Dimensions

    (Height x Width x Depth):

    10 3/4 x 18 3/4 x 6 3/4

    Weight18 lbs.
    Inlets (in)1 1/2'' vent (top) 2'' (sides)
    Power supply120 V - 60 Hz
    Shower/bathtub base min height6" min
    Noise level (measured at 3 ft.)≤ 53 dBA
    Horizontal discharge150 ft
    Vertical discharge15 ft
    Amperage (Amps)4.5 Max
    Operating maximum temperature104°F (110°F Max.)
    Discharge pipe diameter3/4" or 1"
    Tank volume3.1 gallons
    Method of activationMembrane / microswitch
    Discharge rate at 3 ft27 gal/min (103 liters/min)
    Discharge rate at 15 ft17 gal/min (66 liters/min)
    Motor Speed (RPM)3600 rpm tested over 50,000 cycles
    Motor0.5 HP oil-filled thermally protected motor
    Capacitor rating (microfarad)45
    Power cord length (in)51
    Shut off head (ft)30
    Normal running time10-12 sec
    Certifying agenciesCSA (IPC, NSPC) IAPMO (UPC)

    Required Saniaccess 2 Compontents

    All items may be purchased separately.  However, the Saniaccess 3 works as a system and therefore a toilet bowl (083 or 087), toilet tank (005) and the macerating unit (082) need to be purchased.  An optional extension pipe (030) is available for the pump to be installed behind the wall. See complementary products below.

    Additional Product Information

    The inside of the unit is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump. When the flush is activated, the water flowing into the Saniaccess 3 activates a micro switch in the pressure chamber, which starts the motor. The motor is sealed for life in an oil-filled enclosure. A standard spindle/shaft drives the impeller and the macerator blades. The moving parts, therefore, are kept to an absolute minimum. Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.

     

    The centrifugal force causes the reduced solids to be ejected through a grill into the container, where it is picked up by the impeller pump mounted beneath the motor. The unit pumps the effluent upward to 15 feet and 150 feet horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again. A standard operating cycle for Saniaccess 3 takes about 10 - 12 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.

     

    In addition to the toilet waste, the Saniaccess 3 will also discharge gray water from various sanitary fixtures such as a sink, a bathtub, a shower, and a urinal. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2" x 6" (minimum) or 2" x 8" (recommended) on edge to allow for the installation of a P-trap and the required 1/4" per foot gravity flow towards the pump unit.

     

    The wastewater from other sanitary fixtures is discharged into the Saniaccess3 via two 2-inch inlets on either housing side. Either one or both inlets can be used as required. Depending on the discharge installation, the discharge elbow on top of the unit can be turned left, right, or towards the back. A non-return valve, which comes already assembled on the discharge elbow, prevents backflow into the unit.

     

    This unit has been designed with a vent connection on the top of the unit. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. Mechanical vents, air admittance valves, or similar devices are not permitted as these are considered one-way air vent systems. It is also highly recommended that the macerator/pump be connected to a Ground Fault Interrupter (GFI) circuit.

     

    Periodic maintenance can be accomplished quickly without disconnecting the unit from either the toilet or the rest of the plumbing system. Through one service panel, a service contractor can access the electrical components and the level sensor mechanism of the pump. The second service panel provides ready access to the basket area around the macerating blades to easily remove any large objects that may have been accidentally flushed.

     

    The Saniaccess 3 unit must be connected to our rear discharge toilet. This system uses much less water than a regular toilet. Note: This toilet only works in combination with Saniflo systems.

    Certifications

    The Saniaccess 3 has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. 

    Downloads

    Interested in Deals and New Products?

    Keep up-to-date on deals and new home building products that benefit your health, your wealth, and the planet delivered right to your inbox.

    Skip to content